Ingersoll-Rand its part number : 36899706 (old) / 36899706 (new)
Ingersoll Rand PRO-TEC Ponti Oil can normally work in ultra-low temperature; may be at an ambient temperature
of -40 degrees to 52 degrees, can withstand working pressures up to 200PSI; at ambient temperatures from -40
degrees to 18 degrees can withstand working pressures up 350PSI. Designed for high pressure type design; at
operating temperature is between -23 degrees to 52 degrees, working pressure 350PSI more. Pro-Tec (Bao Tai
Yau) applies pressure 300PSI following models, XHP505 for high pressure 300PSI these and other specific
circumstances (such as low temperature). PRO-TEC Ponti oil.
Bao Thai Oil ( 36899706,36899714 )
Ingersoll PRO-TEC oil Ponti main features :
In ultra-low temperature under normal operating synthetics ; ambient temperature of -40 degrees to 52
degrees, can withstand working pressures up to 200PSI; ambient temperature of -40 degrees to 18 degrees,
can withstand working pressures up to 350PSI.
Designed for high pressure type design ; operating temperature is between -23 degrees to 52 degrees ,
working pressure 350PSI more.
Pro-Tec ( Bao Tai Yau ) applies pressure 300PSI following models , XHP505 for high pressure 300PSI these and
other specific circumstances ( such as low temperature ) .
PRO-TEC Po Thai Oil Part Number : 36899706 (5gallon) Applicable models : VHP750/MHP825/HP900/P425E
" Ponti "
Kinematic viscosity (40 ℃), mm2 / s
Kinematic viscosity (100 ℃), mm2 / s
Freezing Point , ℃ (F)
-43 ( -45 )
-48 ( -55 )
-54 ( -65 )
Flash point ( open ), ℃ (F)
188 ( 370 )
227 ( 440 )
216 ( 240 )
Corrosion (T2Cu, 100 ℃, 3h), level
Ingersoll-Rand air compressor cooling oil :
Applicable models ( see filling port )
VHP400/P600/VHP750E/P950E and other older models
Doosan Pro-TEC Compressor Fluid
SECTION 1 COMPOSITION/INFORMATION ONINGREDIENTS
Chemical Names and Synonyms: Severe Treat Min. Oils & Additives
Ingredients Considered Hazardous to Health:
This product is not formulated to contain ingredients, which have exposure limits established by U.S.
agencies. It is not hazardous to health as defined by the European Union Dangerous
SECTION 2 HAZARDS IDENTIFICATION
US OSHA Hazard Communication Standard: Product assessed in accordance with OSHA 29 CFR
1910.1200 and determined not to be hazardous.
Emergency Response Data: Slightly Hazy Amber Liquid. DOT ERG no. -NA
SECTION 3 FIRST AID MEASURES
Eye Contact: Flush thoroughly with water. If irritation occurs, call a physician.
Skin Contact: Wash contact areas with soap and water.
Inhalation: Not expected to be a problem.
Ingestion: Not expected to be a problem. However, if greater than ½ liter (pint) ingested, seek medical
SECTION 4 FIRE-FIGHTING MEASURES
Special Fire Fighting Procedures: Water or foam may cause frothing. Use water to keep fire exposed
containers cool. Water spray may be used to flush spills away from exposure. Prevent runoff from fire control
or dilution from entering streams, sewers, or drinking water supply.
Special Protective Equipment: For fires in enclosed areas, fire fighters must use self-contained breathing
Flammable limits – LEL: NA, UEL: NA.
NFPA Hazard ID: Health: 0, Flammability:1, Reactivity: 0
Hazardous Composition Products: Metal oxides. Carbon monoxide.
SECTION 5 ENVIRONMENTAL AND DISPOSAL INFORMATION
Steps to be Taken in Case of Spills: Soak up with suitable absorbent material, and then sweep into plastic
bag for disposal.
Waste Disposal Method: Dispose in accordance with local, state, or federal regulations.
SECTION 6 HANDLING AND STORAGE
Handling: No special precautions are necessary beyond normal good hygiene practices.
Storage: Do not store in open or unlabelled containers. Store away from strong oxidizing agents or
SECTION 7 EXPOSURE CONTROLS/PERSONAL PROTECTION
Eye Protection: Normal industrial eye protection practices should be employed.
Skin Protection: No special equipment required. However, good personal hygiene practices should always
Exposure Limits: This product does not contain any components which have recognized exposure limits.
However, an exposure limit of 5.00 mg/m3 is suggested for oil mist.
Typical physical properties are given below. Consult Product Data Sheet for specific details.
Color: Slightly Hazy Amber
Odor Threshold-ppm: NE
Boiling Point C(F): >316 (600)
Melting Point C(F): NA
Flash Point C(F): >175 (347) (ASTM D-92)
Auto Flammability: NE
Explosive Properties: NA
Oxidizing Properties: NA
Vapor Pressure –mmHg 20 c: < 0.1
Vapor Density: > 2.0
Evaporation Rate: NE
Relative Density, 15/4 C: 0.87
Solubility in Water: Negligible
Partition Coefficient: > 3.5
Viscosity at 40 C, cSt: 40.0
Viscosity at 100 C, cSt: 7.4
Pour Point C(F): -40 (-40)
Freezing Point C(F): NE
Volatile organic Compound: <8.00 (Wt. %); 0.574 lbs/gal
DMSO Extract, IP-346 (WT.%): < 3, for mineral oil only
NA=NOT APPLICABLE NE=NOT ESTABLISHED D=DECOMPOSES
SECTION 9 STABILITY AND REACTIVITY
Stability(THERMAL, LIGHT, ETC.): Stable.